Message ID | 20220609170520.31162-1-afd@ti.com |
---|---|
State | Accepted |
Delegated to: | Ryan Eatmon |
Headers | show |
Series | [meta-arago,dunfell/master,v2] tisdk-uenv: remove uEnv.txt for k3 | expand |
On Thu, Jun 9, 2022 at 10:05 AM, Andrew Davis wrote: > > This fixup should have been done in u-boot and not in a uEnv.txt > file. It is not correct for all K3 anymore either. Remove it. > > Signed-off-by: Andrew Davis <afd@ti.com> > --- > > Changes from v1: > - Subject s/tiusdk-uenv/tisdk-uenv > > .../tisdk-uenv/tisdk-uenv/k3/uEnv.txt | 19 ------------------- > 1 file changed, 19 deletions(-) > delete mode 100644 > meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt > > diff --git a/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt > b/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt > deleted file mode 100644 > index 80ea34f5..00000000 > --- a/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt > +++ /dev/null > @@ -1,19 +0,0 @@ > -# This uEnv.txt file can contain additional environment settings that you > -# want to set in U-Boot at boot time. This can be simple variables such > -# as the serverip or custom variables. The format of this file is: > -# variable=value > -# NOTE: This file will be evaluated after the bootcmd is run and the > -# bootcmd must be set to load this file if it exists (this is the > -# default on all newer U-Boot images. This also means that some > -# variables such as bootdelay cannot be changed by this file since > -# it is not evaluated until the bootcmd is run. > - Shouldn't we keep the above, as this is generic information about how to use uEnv.txt and when it is invoked? > -# The specific board is not able to be automatically detected. The below is a > -# workaround to set a sane default incase the user has not manually > configured > -# a specific board. > -def_board_name="am65x" > - > -# Check if using default board_name when name_overlays is not set > -check_for_board=if test $name_overlays; then echo "Using board_name = > $board_name"; else setenv board_name $def_board_name; fi > - > -uenvcmd=run check_for_board; run findfdt > -- > 2.36.1 > >
Ryan, I do not see this patch applied to master. Can you check? Thanks Jon -----Original Message----- From: meta-arago@lists.yoctoproject.org <meta-arago@lists.yoctoproject.org> On Behalf Of Jonathan Humphreys via lists.yoctoproject.org Sent: Monday, June 13, 2022 11:18 AM To: meta-arago@lists.yoctoproject.org Subject: Re: [meta-arago] [dunfell/master][PATCH v2] tisdk-uenv: remove uEnv.txt for k3 On Thu, Jun 9, 2022 at 10:05 AM, Andrew Davis wrote: > > This fixup should have been done in u-boot and not in a uEnv.txt file. > It is not correct for all K3 anymore either. Remove it. > > Signed-off-by: Andrew Davis <afd@ti.com> > --- > > Changes from v1: > - Subject s/tiusdk-uenv/tisdk-uenv > > .../tisdk-uenv/tisdk-uenv/k3/uEnv.txt | 19 ------------------- > 1 file changed, 19 deletions(-) > delete mode 100644 > meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt > > diff --git > a/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt > b/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt > deleted file mode 100644 > index 80ea34f5..00000000 > --- > a/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt > +++ /dev/null > @@ -1,19 +0,0 @@ > -# This uEnv.txt file can contain additional environment settings that > you -# want to set in U-Boot at boot time. This can be simple > variables such -# as the serverip or custom variables. The format of this file is: > -# variable=value > -# NOTE: This file will be evaluated after the bootcmd is run and the > -# bootcmd must be set to load this file if it exists (this is the > -# default on all newer U-Boot images. This also means that some > -# variables such as bootdelay cannot be changed by this file since > -# it is not evaluated until the bootcmd is run. > - Shouldn't we keep the above, as this is generic information about how to use uEnv.txt and when it is invoked? > -# The specific board is not able to be automatically detected. The > below is a -# workaround to set a sane default incase the user has not > manually configured -# a specific board. > -def_board_name="am65x" > - > -# Check if using default board_name when name_overlays is not set > -check_for_board=if test $name_overlays; then echo "Using board_name = > $board_name"; else setenv board_name $def_board_name; fi > - > -uenvcmd=run check_for_board; run findfdt > -- > 2.36.1 > > -=-=-=-=-=-=-=-=-=-=-=- Links: You receive all messages sent to this group. View/Reply Online (#13896): https://lists.yoctoproject.org/g/meta-arago/message/13896 Mute This Topic: https://lists.yoctoproject.org/mt/91650730/3617106 Group Owner: meta-arago+owner@lists.yoctoproject.org Unsubscribe: https://lists.yoctoproject.org/g/meta-arago/unsub [j-humphreys@ti.com] -=-=-=-=-=-=-=-=-=-=-=-
It is not applied in master yet. I have not had time to keep it in sync with dunfell given all of the layer changes. I believe Denys will be doing another sync up soon. On 6/26/2022 15:18, Humphreys, Jonathan wrote: > Ryan, I do not see this patch applied to master. Can you check? > > Thanks > Jon > > -----Original Message----- > From: meta-arago@lists.yoctoproject.org <meta-arago@lists.yoctoproject.org> On Behalf Of Jonathan Humphreys via lists.yoctoproject.org > Sent: Monday, June 13, 2022 11:18 AM > To: meta-arago@lists.yoctoproject.org > Subject: Re: [meta-arago] [dunfell/master][PATCH v2] tisdk-uenv: remove uEnv.txt for k3 > > On Thu, Jun 9, 2022 at 10:05 AM, Andrew Davis wrote: > >> >> This fixup should have been done in u-boot and not in a uEnv.txt file. >> It is not correct for all K3 anymore either. Remove it. >> >> Signed-off-by: Andrew Davis <afd@ti.com> >> --- >> >> Changes from v1: >> - Subject s/tiusdk-uenv/tisdk-uenv >> >> .../tisdk-uenv/tisdk-uenv/k3/uEnv.txt | 19 ------------------- >> 1 file changed, 19 deletions(-) >> delete mode 100644 >> meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt >> >> diff --git >> a/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt >> b/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt >> deleted file mode 100644 >> index 80ea34f5..00000000 >> --- >> a/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt >> +++ /dev/null >> @@ -1,19 +0,0 @@ >> -# This uEnv.txt file can contain additional environment settings that >> you -# want to set in U-Boot at boot time. This can be simple >> variables such -# as the serverip or custom variables. The format of this file is: >> -# variable=value >> -# NOTE: This file will be evaluated after the bootcmd is run and the >> -# bootcmd must be set to load this file if it exists (this is the >> -# default on all newer U-Boot images. This also means that some >> -# variables such as bootdelay cannot be changed by this file since >> -# it is not evaluated until the bootcmd is run. >> - > > Shouldn't we keep the above, as this is generic information about how to use uEnv.txt and when it is invoked? > >> -# The specific board is not able to be automatically detected. The >> below is a -# workaround to set a sane default incase the user has not >> manually configured -# a specific board. >> -def_board_name="am65x" >> - >> -# Check if using default board_name when name_overlays is not set >> -check_for_board=if test $name_overlays; then echo "Using board_name = >> $board_name"; else setenv board_name $def_board_name; fi >> - >> -uenvcmd=run check_for_board; run findfdt >> -- >> 2.36.1 >> >> > > > -=-=-=-=-=-=-=-=-=-=-=- > Links: You receive all messages sent to this group. > View/Reply Online (#13896): https://lists.yoctoproject.org/g/meta-arago/message/13896 > Mute This Topic: https://lists.yoctoproject.org/mt/91650730/3617106 > Group Owner: meta-arago+owner@lists.yoctoproject.org > Unsubscribe: https://lists.yoctoproject.org/g/meta-arago/unsub [j-humphreys@ti.com] > -=-=-=-=-=-=-=-=-=-=-=- > >
I don't think the layer changes will have any impact on it. +Denys -----Original Message----- From: Eatmon, Ryan <reatmon@ti.com> Sent: Monday, June 27, 2022 11:00 AM To: Humphreys, Jonathan <j-humphreys@ti.com>; meta-arago@lists.yoctoproject.org Subject: Re: [meta-arago] [dunfell/master][PATCH v2] tisdk-uenv: remove uEnv.txt for k3 It is not applied in master yet. I have not had time to keep it in sync with dunfell given all of the layer changes. I believe Denys will be doing another sync up soon. On 6/26/2022 15:18, Humphreys, Jonathan wrote: > Ryan, I do not see this patch applied to master. Can you check? > > Thanks > Jon > > -----Original Message----- > From: meta-arago@lists.yoctoproject.org > <meta-arago@lists.yoctoproject.org> On Behalf Of Jonathan Humphreys > via lists.yoctoproject.org > Sent: Monday, June 13, 2022 11:18 AM > To: meta-arago@lists.yoctoproject.org > Subject: Re: [meta-arago] [dunfell/master][PATCH v2] tisdk-uenv: > remove uEnv.txt for k3 > > On Thu, Jun 9, 2022 at 10:05 AM, Andrew Davis wrote: > >> >> This fixup should have been done in u-boot and not in a uEnv.txt file. >> It is not correct for all K3 anymore either. Remove it. >> >> Signed-off-by: Andrew Davis <afd@ti.com> >> --- >> >> Changes from v1: >> - Subject s/tiusdk-uenv/tisdk-uenv >> >> .../tisdk-uenv/tisdk-uenv/k3/uEnv.txt | 19 ------------------- >> 1 file changed, 19 deletions(-) >> delete mode 100644 >> meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt >> >> diff --git >> a/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt >> b/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt >> deleted file mode 100644 >> index 80ea34f5..00000000 >> --- >> a/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt >> +++ /dev/null >> @@ -1,19 +0,0 @@ >> -# This uEnv.txt file can contain additional environment settings >> that you -# want to set in U-Boot at boot time. This can be simple >> variables such -# as the serverip or custom variables. The format of this file is: >> -# variable=value >> -# NOTE: This file will be evaluated after the bootcmd is run and the >> -# bootcmd must be set to load this file if it exists (this is the >> -# default on all newer U-Boot images. This also means that some >> -# variables such as bootdelay cannot be changed by this file since >> -# it is not evaluated until the bootcmd is run. >> - > > Shouldn't we keep the above, as this is generic information about how to use uEnv.txt and when it is invoked? > >> -# The specific board is not able to be automatically detected. The >> below is a -# workaround to set a sane default incase the user has >> not manually configured -# a specific board. >> -def_board_name="am65x" >> - >> -# Check if using default board_name when name_overlays is not set >> -check_for_board=if test $name_overlays; then echo "Using board_name >> = $board_name"; else setenv board_name $def_board_name; fi >> - >> -uenvcmd=run check_for_board; run findfdt >> -- >> 2.36.1 >> >> > > > -=-=-=-=-=-=-=-=-=-=-=- > Links: You receive all messages sent to this group. > View/Reply Online (#13896): > https://lists.yoctoproject.org/g/meta-arago/message/13896 > Mute This Topic: https://lists.yoctoproject.org/mt/91650730/3617106 > Group Owner: meta-arago+owner@lists.yoctoproject.org > Unsubscribe: https://lists.yoctoproject.org/g/meta-arago/unsub > [j-humphreys@ti.com] > -=-=-=-=-=-=-=-=-=-=-=- > > -- Ryan Eatmon reatmon@ti.com ----------------------------------------- Texas Instruments, Inc. - LCPD - MGTS
Not this one, but there are a number of other patches in line before it that might be. On 6/27/2022 11:02, Humphreys, Jonathan wrote: > I don't think the layer changes will have any impact on it. > > +Denys > > > -----Original Message----- > From: Eatmon, Ryan <reatmon@ti.com> > Sent: Monday, June 27, 2022 11:00 AM > To: Humphreys, Jonathan <j-humphreys@ti.com>; meta-arago@lists.yoctoproject.org > Subject: Re: [meta-arago] [dunfell/master][PATCH v2] tisdk-uenv: remove uEnv.txt for k3 > > > It is not applied in master yet. I have not had time to keep it in sync with dunfell given all of the layer changes. I believe Denys will be doing another sync up soon. > > > > On 6/26/2022 15:18, Humphreys, Jonathan wrote: >> Ryan, I do not see this patch applied to master. Can you check? >> >> Thanks >> Jon >> >> -----Original Message----- >> From: meta-arago@lists.yoctoproject.org >> <meta-arago@lists.yoctoproject.org> On Behalf Of Jonathan Humphreys >> via lists.yoctoproject.org >> Sent: Monday, June 13, 2022 11:18 AM >> To: meta-arago@lists.yoctoproject.org >> Subject: Re: [meta-arago] [dunfell/master][PATCH v2] tisdk-uenv: >> remove uEnv.txt for k3 >> >> On Thu, Jun 9, 2022 at 10:05 AM, Andrew Davis wrote: >> >>> >>> This fixup should have been done in u-boot and not in a uEnv.txt file. >>> It is not correct for all K3 anymore either. Remove it. >>> >>> Signed-off-by: Andrew Davis <afd@ti.com> >>> --- >>> >>> Changes from v1: >>> - Subject s/tiusdk-uenv/tisdk-uenv >>> >>> .../tisdk-uenv/tisdk-uenv/k3/uEnv.txt | 19 ------------------- >>> 1 file changed, 19 deletions(-) >>> delete mode 100644 >>> meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt >>> >>> diff --git >>> a/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt >>> b/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt >>> deleted file mode 100644 >>> index 80ea34f5..00000000 >>> --- >>> a/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt >>> +++ /dev/null >>> @@ -1,19 +0,0 @@ >>> -# This uEnv.txt file can contain additional environment settings >>> that you -# want to set in U-Boot at boot time. This can be simple >>> variables such -# as the serverip or custom variables. The format of this file is: >>> -# variable=value >>> -# NOTE: This file will be evaluated after the bootcmd is run and the >>> -# bootcmd must be set to load this file if it exists (this is the >>> -# default on all newer U-Boot images. This also means that some >>> -# variables such as bootdelay cannot be changed by this file since >>> -# it is not evaluated until the bootcmd is run. >>> - >> >> Shouldn't we keep the above, as this is generic information about how to use uEnv.txt and when it is invoked? >> >>> -# The specific board is not able to be automatically detected. The >>> below is a -# workaround to set a sane default incase the user has >>> not manually configured -# a specific board. >>> -def_board_name="am65x" >>> - >>> -# Check if using default board_name when name_overlays is not set >>> -check_for_board=if test $name_overlays; then echo "Using board_name >>> = $board_name"; else setenv board_name $def_board_name; fi >>> - >>> -uenvcmd=run check_for_board; run findfdt >>> -- >>> 2.36.1 >>> >>> >> >> >> -=-=-=-=-=-=-=-=-=-=-=- >> Links: You receive all messages sent to this group. >> View/Reply Online (#13896): >> https://lists.yoctoproject.org/g/meta-arago/message/13896 >> Mute This Topic: https://lists.yoctoproject.org/mt/91650730/3617106 >> Group Owner: meta-arago+owner@lists.yoctoproject.org >> Unsubscribe: https://lists.yoctoproject.org/g/meta-arago/unsub >> [j-humphreys@ti.com] >> -=-=-=-=-=-=-=-=-=-=-=- >> >> >
Jon, This particular change is rather trivial, indeed. Other changes are more involved due to override syntax change and meta-ti restructure. I am collecting recent changes in Dunfell and will do another sync with Kirkstone/master soon.
diff --git a/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt b/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt deleted file mode 100644 index 80ea34f5..00000000 --- a/meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt +++ /dev/null @@ -1,19 +0,0 @@ -# This uEnv.txt file can contain additional environment settings that you -# want to set in U-Boot at boot time. This can be simple variables such -# as the serverip or custom variables. The format of this file is: -# variable=value -# NOTE: This file will be evaluated after the bootcmd is run and the -# bootcmd must be set to load this file if it exists (this is the -# default on all newer U-Boot images. This also means that some -# variables such as bootdelay cannot be changed by this file since -# it is not evaluated until the bootcmd is run. - -# The specific board is not able to be automatically detected. The below is a -# workaround to set a sane default incase the user has not manually configured -# a specific board. -def_board_name="am65x" - -# Check if using default board_name when name_overlays is not set -check_for_board=if test $name_overlays; then echo "Using board_name = $board_name"; else setenv board_name $def_board_name; fi - -uenvcmd=run check_for_board; run findfdt
This fixup should have been done in u-boot and not in a uEnv.txt file. It is not correct for all K3 anymore either. Remove it. Signed-off-by: Andrew Davis <afd@ti.com> --- Changes from v1: - Subject s/tiusdk-uenv/tisdk-uenv .../tisdk-uenv/tisdk-uenv/k3/uEnv.txt | 19 ------------------- 1 file changed, 19 deletions(-) delete mode 100644 meta-arago-distro/recipes-tisdk/tisdk-uenv/tisdk-uenv/k3/uEnv.txt